M10 Revolving Handle Fits Any M10 Thread - Trailer Jack, Hose Reel & More | 76mm (2.99") Free-Spinning Grip, 100mm (3.94") Overall - PA6 Nylon on C450($11.19Value)

Description

This M10 x P1.5 revolving handle pairs an engineering-grade Nylon (PA6) grip with a steel spindle (C450) and a steel nut, both finished in yellow-zinc to resist rust, so a trailer jack handle or hose reel handle keeps turning after seasons outdoors. Rated for a -4F to 200F range and built for a 20+ year service life, this threaded handle resists cracking in cold and softening in heat, giving a boat trailer jack handle the same dependable feel through marine spray and workshop use. Arriving pre-assembled with an anti-loosening fixing nut, this crank handle replacement threads onto your M10 x P1.5 shaft and tightens with a Phillips screwdriver for a hold that will not back off under repeated cranking. Unlike a worn hand crank handle that wobbles loose, this trailer handle replacement and trailer jack replacement handle stays snug through towing vibration, so a jack handle replacement you install once keeps working instead of loosening again. The 76mm grip on this revolving handle knob spins smoothly under load instead of forcing your wrist to fight a fixed knob, turning a stiff, awkward crank into an easy rotating handle motion. As a spinning handle and swivel handle in one, it doubles as a trailer jack knob for boat and utility trailers and a hose reel crank handle for garden reels, so raising a jack or reeling in a hose leaves your hand less fatigued, and the revolving hand knob keeps turning cleanly for years. Beyond towing gear, this M10 x P1.5 crank works as a table saw fence handle and table saw crank handle for blade-height adjustment, a drill press handle for quill feed, and a lathe tailstock or milling crank once the thread matches many popular parts. It also stands in as a trailer tongue jack handle, trailer winch handle or boat trailer crank handle for utility and camper trailers, once you confirm the M10 x P1.5 thread against your existing part. This revolving handle m10 measures 76mm (2.99 in) at the plastic grip, 100mm (3.94 in) total length once the threaded bolt is included, and 25mm (0.98 in) across the grip diameter, on an M10 x P1.5 thread built for pressure washer hose reel handle, trailer jack handles and crank handles alike. Because the total counts the bolt, measure your shaft and compare it with your old trailer handle crank or jack handle before ordering this DONGYANG piece, made in Korea. The DONGYANG M10 x P1.5 revolving handle is a heavy-duty trailer jack handle replacement and hose reel handle replacement, fitting boat trailer jacks, utility trailer tongue jacks, camper jacks, garden and water hose reels, and welding cable reels. The 76mm grip spins smoothly under load, so this crank handle cuts hand fatigue during repeated cranking, turning a stiff factory knob into an easy rotating handle motion. Beyond towing and reel duty, this handle doubles as a table saw fence handle, lathe tailstock crank, drill press handle and milling machine crank, and works as a swivel handle across many popular parts once the M10 x P1.5 thread is confirmed to match your machine. Construction pairs an engineering-grade Nylon (PA6) grip with a steel spindle (C450) and steel nut, both finished in yellow-zinc to resist rust. Rated for a -4F to 200F range with a 20+ year service life, it holds up to marine spray and workshop oil without cracking in cold or softening in heat. It arrives pre-assembled with an anti-loosening fixing nut, so it stays tight through repeated cranking instead of working loose like a worn hand crank handle. Sizing: M10 x P1.5 thread, plastic grip length 76mm (2.99 in), total length 100mm (3.94 in) including the threaded bolt, grip diameter 25mm (0.98 in). Measure your old trailer jack handle or hose reel crank handle thread and length and compare it against this chart before ordering. Made in Korea by DONGYANG.